Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Blog Article
The publisher is making a number of great annotation about Installing A Bathtub as a whole in this post following next.
Setting up a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently available, the job can relocate quickly; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified on your own for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to think about using one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also don't need to alter the plan of your previous water system pipelines.
Your devices and also material checklist ought to comprise the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the restricted accessibility that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has actually been used a minimum of once as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place feedback down below. We would be pleased to find out your feelings about this blog entry. We hope that you come back again in the near future. In case you enjoyed our page please make sure you remember to share it. I cherish reading our article about How to Install a Bathtub Yourself.
Automated Marketing
Report this page